The Phoenix Project 2.0
-
The Twin Towers are in their final days.
-
The most straightforward approach has one downside - the necessity to refill water almost daily to ensure the stems are completely immersed. It typically takes around two weeks for sufficient roots to develop for a successful shift to soil-based growth.
-
The first generation is approaching its final stages; a higher-quality close-up camera aids in masking the general untidiness by enhancing the crystal's quality.
-
The most straightforward method has a minor disadvantage - the requirement to replenish water almost daily to ensure that the stems are completely immersed. It typically takes around two weeks for sufficient roots to develop for a successful shift to soil-based growth.
-
After the water-based cloning didn't yield the desired results, I opted to try planting a couple directly in soil, using honey as a natural stimulant to encourage root growth.
-
The yellowing of the older sun leaves is becoming more noticeable as budding begins, indicating that it's time for me to tackle my inadequate nutrient management.
-
The Twin Towers are in their final days.
-
This duo spent nearly a week outside, transitioning from 3-gallon to approximately 7-gallon containers, showing no signs of distress.
The seed-derived duo housed in coffee containers have been outdoors from the time they were planted. They exhibit a strikingly different structure, with significantly wider gaps between nodes, even though they are exposed to natural sunlight.
-
In a state where I can't freely access or grow my own plants, I'm focusing on nurturing a single female plant to optimize my indoor garden, ensuring my self-reliance. By harvesting the bottom half, enough foliage is left for regeneration and replication for future plantings. As these offshoots grow, they will also provide new clones, ideally female.
Next to her, I've set up two containers that I've found useful for both seed and clone-based growth - their design allows for easy relocation of successful sprouts, facilitating a stronger base for the initial stages of my usual two-month growth cycle. I'm using a Spiderfarmer SF1000 light within a sturdy shelving unit enclosure, and as new cuttings emerge, I have two larger cabinets and two smaller sprouting stations to accommodate as many as I wish.
By following my rigorous pruning and training regimen, I can maximize the potential of my garden, saving me from spending my retirement funds on secretive self-treatment and enjoyment.
Take a peek,
All the best! -
A quick look at the progress of the Phoenix Project reveals it's a little tight but still under control.
-
Residing in a state where I'm denied the liberty to cultivate my own crops or even purchase seeds for diversifying my taste, I've decided to set aside a female plant to serve as the linchpin for my indoor garden, enabling me to stay self-reliant. By sparing the lower section during harvest, I am left with sufficient foliage to rejuvenate and become a source for generating clones for my upcoming cycles. As these cuttings grow, they will provide clones, which I hope will be confirmed females.
Surrounding this plant are a couple of pots I've found useful for both seed and clone-based endeavors - the multi-layered system provides a convenient home for successful sprouts that only need simple relocation for developing a solid foundation during my usual two-month vegetation phase. The lighting for this setup is a Spiderfarmer SF1000 housed within a sturdy shelving unit, and as cuttings become available, I have two larger cabinets and two smaller sprouting stations to accommodate as many as I wish.
A glance at my aggressive topping and training regimen provides a blueprint for all my efforts, thereby increasing the likelihood of freeing me from using my retirement funds for covert self-medication and amusement.Feel free to take a closer look,
Best of luck! -
I enjoy using a homemade cloning machine for my cloning projects, which is both simple to use and enjoyable. I've even provided a guide on how to construct your own cloning machine. If I don't see any progress after a period of 10 days, I typically begin the process again. Best wishes!
-
Living in a region where I'm not permitted to freely cultivate or even buy seeds or clones to enhance my taste, I've decided to use a female plant as a source for my indoor garden to increase its productivity and ensure my self-reliance. By cutting off the lower half during harvest, I can allow enough foliage to re-grow and serve as a source for future clone propagation. As these cuttings grow, they'll provide new clones that are more likely to be female.
On either side of her, there are two containers that I've found are useful for stabilizing both seed- and clone-based plants. Their design provides a ready-to-use home for thriving seedlings, making it easy to establish a strong base for the initial two phases of my regular two-month vegetation process. I use a Spiderfarmer SF1000 light in an enclosure made from a sturdy shelving unit for this, and I have two larger cabinets and two smaller sprouting stations ready to accommodate as many cuttings as needed.
An overview of my rigorous topping and training routine provides a blueprint for all my operations, enhancing the possibility of maintaining my independence from spending my retirement funds on clandestine self-medication and entertainment.
-
8000 cups of coffee enables work in an open-air initiative parallel to the Phoenix Project's launch. Twenty vessels were sowed last night, each receiving three seeds directly into the soil. The aim is to observe how the sun's natural light fares against my indoor lighting system.
-
As the budding phase begins, the yellowing of the older Sun leaves is becoming more noticeable. This means I can no longer ignore my subpar nutrient management issue and must tackle it soon.
-
Living in a state where I can't freely cultivate or purchase seeds or clones to expand my taste, I've decided to keep a female plant as a mother to improve my indoor garden's efficiency and ensure my self-reliance. By sparing the lower part during harvest, I've managed to have enough foliage for rejuvenation and to serve as a source for future clones. As these cuttings grow, they'll provide me with new clones, which I hope will be female.
Adjacent to her, I have two containers that I've found useful for stabilizing both seed-based and clone-based projects - the nested system offers a ready-made home for successful sprouts, requiring only a simple move and drop to develop a stronger base for the initial two stages of my usual two-month vegetative routine. I use a Spiderfarmer SF1000 light in an enclosure made from a heavy-duty shelving unit, and as new cuttings appear, I have two larger cabinets and two smaller sprouting stations that can accommodate as many as I want.
My aggressive topping and training program's typical setup provides a blueprint for all my efforts, increasing the possibility of sustaining myself without having to spend my retirement funds on covert self-medication and leisure.
Take a look - best of luck.
-
The goal is to cultivate a autumn harvest, including radish, green beans, and squash, with plans to transfer them into larger containers by the end of the week.
-
Interestingly, the two stumps that are now regrowing were the same ones shown last September. They were hastily made to bloom and unfortunately didn't reach their utmost potential.
-
The aim is to cultivate a Autumn harvest of radish, green beans, and squash, with plans to transfer them into larger pots by the week's end.
-
Working outdoors alongside the Phoenix Project, 8000 coffee cups serve as a unique opportunity. Twenty containers, each filled with three seeds, were directly planted in soil last night. This is an experiment to compare the growth potential offered by the natural sunlight versus my extensive indoor lighting system.